Two-component, solvent-based flooring resin, perfect for industrial applications. Creates coatings that are highly resistant mechanically and chemically. It is easy to clean and dirt does not adhere to it.
Neopox Special floor epoxy resin is a two-component solvent-based resin that is perfect for painting floors and lines in warehouses, garages, industrial halls, and food production and processing halls. The resin creates coatings that are highly chemically and mechanically resistant, so they can be easily traversed by e.g. forklifts. The coating is characterized by a high gloss, making it easy to keep clean and dirt does not adhere to it.
Good resistance to solvents and diluted acids (full chemical resistance table can be found in the technical data sheet, available for download under the product description),
Suitable as a protective coating for biological treatment plants.
Neopox Special - systemic primers:
CONCRETE:ApplyEpoxol Primer diluted with epoxy thinner in the amount of 10-15%, orEpoxol Primer SF-P . FRESH OR DAMP CONCRETE: Use Neopox Primer WS . Concrete must be at least 2 weeks old. Moisture in concrete cannot result from capillary rising of moisture from the ground, but from, for example, rainfall or frequent cleaning procedures and the inability to dry the substrate. CAPILLARY CONCRETE, FROM GROUND:Neopox Primer AY epoxy primer . ANHYDRITE, SCREED, OTHER HIGH ABSORPTION FLOOR SCREED: Use solvent-based epoxy primer Epoxol Primer diluted 10-15% with Neotex 1021 . Anhydrite or screed are poor-quality substrates with high absorbency, therefore the primer consumption may be higher than indicated in the technical data sheet. TILES, GLOSS POLISHED CONCRETE: In the case of non-absorbent substrates, use Super Binder RO3333 . METAL SUBSTRATES: Apply one layer of Neopox Primer 815 diluted 8-10% with Neotex 1021 to protect against corrosion. POLYESTER AND WOOD: the substrate should be rough (not smooth), level, and free from dust, dirt, greasy and oily substances. Apply one layer of Neopox Special diluted with 8% Neotex 1021 . Dilute the second layer with 4-8%. If a third layer is necessary, dilute it to 4%. If the wood is very absorbent, prime it with Epoxol Primer diluted 10-15% with Neotex 1021 .
Neopox Special epoxy floor coating - surface preparation and application:
The substrate must be clean, dry (moisture content below 4%) and free from any contamination, such as dirt, oil, grease, impregnation, etc. Cement laitance should be removed. Fill local holes/cracks with Epoxol Putty . Before application, combine the A&B ingredients and mix them thoroughly in appropriate proportions by weight. Mix with a low-speed mechanical mixer, making sure to mix the product thoroughly also at the walls and bottom. Neopox Special is a two-component resin (the price is for the set, i.e. base with hardener).
Economical epoxy resin
When looking for concrete paint for painting floors in industrial facilities, it is worth choosing epoxy products. They are characterized by high resistance to mechanical damage and chemical agents, making them perfect for places where heavy machine traffic takes place. the epoxy coating has !
Industrial epoxy coating – why is it worth using in your project?
Finishing the floor in industrial facilities is quite a challenge - you need to choose flooring systems that are durable, resistant and at the same time easy to keep clean. These requirements are met by epoxy resin for garages , which can also be used in warehouses, car workshops or indoor parking lots - for painting lines. We offer products in many color options. They are resistant to:
exposure to extreme temperatures,
water – including sea and fresh water,
chemicals including dilute acids and solvents.
Choose epoxy coatings from our offer!
If you care about an aesthetic finish of the surface, clearly painted lines and a durable floor that will survive industrial conditions - products from this category will be a hit! Use them in your project and you can be sure that the substrate will remain in good condition for a long time without the need for repeated renovation. You don't know if economical epoxy resin is the right solution? Contact us – we will advise you!
Do you have any questions? We will help you choose the perfect product to use.
NOTE: WATER-BASED PRODUCT. Choose temperature-controlled shipping to receive the product on the declared date, regardless of the weather. Standard shipments may be held due to temperatures below 5°C along the delivery route.
Solvent-based epoxy primer for epoxy paints, polyurethane resins. For use on floors and walls where high mechanical and chemical resistance is required.
Primer for epoxy, acrylic and polyurethane topcoats. Durable in changing weather conditions, constant contact with water and industrial atmosphere. Provides anti-corrosion protection and excellent adhesion.
Two-component putty for a wide range of applications. Depending on the mixing ratio of the ingredients, you can obtain a flexible, hard or very hard mass. Recommended for metal, concrete, wood and ceramics. Also for car and yacht repairs.
Let us know what you need and we will even match products to your project on the same day.
Need advice?
We will choose the right solution
FAQ: Frequently asked questions
How long does a given resin dry?
keyboard_arrow_downkeyboard_arrow_up
All epoxy resins have similar drying times.The coating stops being sticky after just a few hours, but the next layer should be applied after 24-36 hours.After applying the last layer, the coating fully hardens (chemically and mechanically) after 7 days.During this time, it is best not to use the floor, especially not to wash it with water or any cleaning agents.The drying and hardening time depends on the ambient and substrate temperature.In the case of Neopox Special resin, the minimum required temperature is +12°C, however, we always recommend that when applying epoxy resins, the temperature should be approximately 20-22°C.Thanks to this, we can be sure that the coating will harden properly and will have good strength parameters.
Epoxy resin for concrete - how to paint?
keyboard_arrow_downkeyboard_arrow_up
Epoxy resins consist of two components - a base and a hardener.These are the so-calledself-curing resins, which means that they harden due to a chemical reaction between the ingredients.Before painting, you must thoroughly mix the base and hardener in the appropriate proportion.In the case of Neopox Special, the weight proportion is 3:1 (e.g. 300 grams of base + 100 grams of hardener).After combining the ingredients, the mixture should be used within the specified time specified in the product data sheet.After this time, the resin is unsuitable for use.Neopox Special resin is applied with a roller, brush or spray, diluting it appropriately.
Is NEOPOX SPECIAL also a coating for outdoor concrete?
Coatings based on epoxy resin are waterproof and chemically resistant. Therefore, they work perfectly on floors, are easy to keep clean and protect concrete against contamination.
Epoxy resin for flooring - what are its advantages?
keyboard_arrow_downkeyboard_arrow_up
By painting the floor with epoxy resin, we obtain a uniform, smooth coating, without any joints (except for possible expansion joints).This is a very big advantage compared to, for example, tiles, where the grout is difficult to clean.Additionally, these coatings are chemically resistant, so they are not afraid of dripping oil or road salt on car wheels.
Two-component, solvent-based flooring resin, perfect for industrial applications. Creates coatings that are highly resistant mechanically and chemically. It is easy to clean and dirt does not adhere to it.
Order in bulk with free advice
Get a discount for your company by talking to an advisor.
NOTE: WATER-BASED PRODUCT. Choose temperature-controlled shipping to receive the product on the declared date, regardless of the weather. Standard shipments may be held due to temperatures below 5°C along the delivery route.
Single-component, quick-drying road paint for horizontal marking of concrete, asphalt, paving stones - traffic permitted after 11 minutes . Highly resistant to abrasion - necessary in warehouses, garages and parking lots. Bandax road strip and line paint has Institute of Hygiene Certificate and the National Certificate of Conformity.
Trken Floor Protect 3in1 is a two -component, environmentally friendly epoxy resin based on water. Thanks to specially selected components, as one product has three uses. It can be used as an epoxy soil, a leveling mass, as well as a smooth surface layer. Trken Floor Protect 3in1 is based on epoxy resin resistant to oil, lubricant, fuel and other chemicals. Low LZO content allows the use of a product in garages, industrial halls as well as residential buildings and public facilities.
NOTE: WATER-BASED PRODUCT. Choose temperature-controlled shipping to receive the product on the declared date, regardless of the weather. Standard shipments may be held due to temperatures below 5°C along the delivery route.
Trken Floor Fast Special is a thick -hexis, quickly hardening, self -leveling epoxy resin, which is intended for industrial applications and decorative projects that require a perfectly smooth surface. The product provides the possibility of applying 1 to even 15 mm of resin in one layer. It is characterized by very low emission of volatile organic compounds (LZO), thanks to which it is practically odorless.
Epoxy resin for floor screeds. Self-leveling and solvent-free, resistant to chemicals (alkalis, diluted acids, gasoline, oils and many solvents), available in many colors from the RAL palette. It has a Greek hygiene certificate and a certificate for contact with food and alcohol - it can be used in places of food production and processing.
Epoxol®RM-YR is a two-component, solvent-free, transparent epoxy resin that does not contain fillers. Perfect for industrial and decorative floors filled with colored aggregate.